1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。 水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。 设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环境条件等最后确定截面。钢筋混凝土通常是现场浇注的合成材料，它与在工厂中制造的标准的钢结构梁、柱等不同，因此对于上面所提到的一系列因素必须予以考虑。 对结构体系的各个部位均需选定试算截面并进行验算，以确定该截面的名义强度是否足以承受所作用的计算荷载。由于经常需要进行多次试算，才能求出所需的 3 截面，因此设计时第一次采用的数值将导致一系列的试算与调整工作。 选择混凝土截面时，采用试算与调整过程可以使复核与设计结合在一起。因此，当试算截面选定后，每次设计都是对截面进行复核。手册、图表和微型计算机以及专用程序的使用，使这种设计方法更为简捷有效，而传统的方法则是把钢筋混凝土的复核与单纯的设计分别进行处理。 2土方工程 由于和土木工程中任何其他工种的施工方法与费用相比较，土方挖运的施工方法与费用的变化都要快得多，因此对于有事业心的人来说，土方工程是一个可以大有作为的领域。在1935年，目前采用的利用轮胎式机械设备进行土方挖运的方法大多数还没有出现。那是大部分土方是采用窄轨铁路运输，在这目前来说是很少采用的。当时主要的开挖方式是使用正铲、反铲、拉铲或抓斗等挖土机，尽管这些机械目前仍然在广泛应用，但是它们只不过是目前所采用的许多方法中的一小部分。因此，一个工程师为了使自己在土方挖运设备方面的知识跟得上时代的发展，他应当花费一些时间去研究现代的机械。一般说来，有关挖土机、装载机和运输机械的唯一可靠而又最新的资料可以从制造厂商处获得。 土方工程或土方挖运工程指的是把地表面过高处的土壤挖去（挖方），并把它倾卸到地表面过低的其他地方（填方）。为了降低土方工程费用，填方量应该等于挖方量，而且挖方地点应该尽可能靠近土方量相等的填方地点，以减少运输量和填方的二次搬运。土方设计这项工作落到了从事道路设计的工程师的身上，因为土方工程的设计比其他任何工作更能决定工程造价是否低廉。根据现有的地图和标高，道路工程师应在设计绘图室中的工作也并不是徒劳的。它将帮助他在最短的时间内获得最好的方案。 费用最低的运土方法是用同一台机械直接挖方取土并且卸土作为填方。这并不是经常可以做到的，但是如果能够做到则是很理想的，因为这样做既快捷又省钱。拉铲挖土机。推土机和正铲挖土机都能做到这点。拉铲挖土机的工作半径最大。推土机所推运的图的数量最多，只是运输距离很短。拉铲挖土机的缺点是只能挖比它本身低的土，不能施加压力挖入压实的土壤内，不能在陡坡上挖土，而且挖。卸都不准确。 正铲挖土机介于推土机和拉铲挖土机的之间，其作用半径大于推土机，但小于拉铲挖土机。正铲挖土机能挖取竖直陡峭的工作面，这种方式对推土机司机来说是危险的，而对拉铲挖土机则是不可能的。每种机械设备应该进行最适合它的性能的作业。正铲挖土机不能挖比其停机平面低很多的土，而深挖坚实的土壤时，反铲挖土机最适用，但其卸料半径比起装有正铲的同一挖土机的卸料半径则要小很多。在比较平坦的场地开挖，如果用拉铲或正铲挖土机运输距离太远时，则装有轮胎式的斗式铲运机就是比不可少的。它能在比较平的地面上挖较深的土（但只能挖机械本身下面的土），需要时可以将土运至几百米远，然后卸土并在卸土的过程中把土大致铲平。在挖掘硬土时，人们发现在开挖场地经常用一辆助推拖拉机（轮式或履带式），对返回挖土的铲运机进行助推这种施工方法是经济的。一旦铲运机装满，助推拖拉机就回到开挖的地点去帮助下一台铲运机。 斗式铲运机通常是功率非常大的机械，许多厂家制造的铲运机铲斗容量为8 m³，满载时可达10 m³。最大的自行式铲运机铲斗容量为19立方米（满载时为25 m³），由430马力的牵引发动机驱动。 翻斗机可能是使用最为普遍的轮胎式运输设备，因为它们还可以被用来送混凝土或者其他建筑材料。翻斗车的车斗位于大橡胶轮胎车轮前轴的上方，尽管铰接式翻斗车的卸料方向有很多种，但大多数车斗是向前翻转的。最小的翻斗车的容量大约为5立方米，而最大的标准型翻斗车的容量大约为5m³。特殊型式的翻斗车包括容量为4 m³的自装式翻斗车，和容量约为5 m³的铰接式翻斗车。必须记住翻斗车与自卸卡车之间的区别。翻斗车车斗向前倾翻而司机坐在后方卸载，因此有时被称为后卸卡车。 3结构的安全度 规范的主要目的是提供一般性的设计原理和计算方法，以便验算结构的安全度。就目前的趋势而言，安全系数与所使用的材料性质及其组织情况无关，通常把它定义为发生破坏的条件与结构可预料的最不利的工作条件之比值。这个比值还与结构的破坏概率（危险率）成反比。 破坏不仅仅指结构的整体破坏，而且还指结构不能正常的使用，或者，用更为确切的话来说，把破坏看成是结构已经达到不能继续承担其设计荷载的“极限状态”。通常有两种类型的极限状态，即： （1）强度极限状态，它相当于结构能够达到的最大承载能力。其例子包括结构的局部屈曲和整体不稳定性；某此界面失效，随后结构转变为机构；疲劳破坏；引起结构几何形状显著变化的弹性变形或塑性变形或徐变；结构对交变荷载、火灾和爆炸的敏感性。 （2）使用极限状态，它对应着结构的使用功能和耐久性。器例子包括结构失稳之前的过大变形和位移；早期开裂或过大的裂缝；较大的振动和腐蚀。 根据不同的安全度条件，可以把结构验算所采用的计算方法分成： （1）确定性的方法，在这种方法中，把主要参数看作非随机参数。 （2）概率方法，在这种方法中，主要参数被认为是随机参数。此外，根据安全系数的不同用途，可以把结构的计算方法分为： （1）容许应力法，在这种方法中，把结构承受最大荷载时计算得到的应力与经过按规定的安全系数进行折减后的材料强度作比较。 （2）极限状态法，在这种方法中，结构的工作状态是以其最大强度为依据来衡量的。由理论分析确定的这一最大强度应不小于结构承受计算荷载所算得的强度（极限状态）。计算荷载等于分别乘以荷载系数的活载与恒载之和。 把对应于不乘以荷载系数的活载和恒载的工作（使用）条件的应力与规定值（使用极限状态）相比较。根据前两种方法和后两种方法的四种可能组合，我们可以得到一些实用的计算方法。通常采用下面两种计算方法： 确定性的方法，这种方法采用容许应力。 概率方法，这种方法采用极限状态。 至少在理论上，概率法的主要优点是可以科学的考虑所有随机安全系数，然后将这些随机安全系数组合成确定的安全系数。概率法取决于： 1 Reinforced Concrete Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete It is this deviation in the composition of a reinforces concrete section from the homogeneity of 答题实属不易，请楼主谅解，求采纳~
ma of more days and months and years t
外文原文可以去检索下载中文要自己搞定了～～～还有疑问联系我
对土木工程的发展起关键作用的，首先是作为工程物质基础的土木建筑材料，其次是随之发展起来的设计理论和施工技术。每当出现新的优良的建筑材料时，土木工程就 会有飞跃式的发展。 人们在早期只能依靠泥土、木料及其它天然材料从事营造活动，后来出现了砖和瓦这种人工建筑材料，使人类第一次冲破了天然建筑材料的束缚。中国在公元前十一世纪 的西周初期制造出瓦。最早的砖出现在公元前五世纪至公元前三世纪战国时的墓室中。砖和瓦具有比土更优越的力学性能，可以就地取材，而又易于加工制作。 砖和瓦的出现使人们开始广泛地、大量地修建房屋和城防工程等。由此土木工程技术得到了飞速的发展。直至18～19世纪，在长达两千多年时间里，砖和瓦一直是土木工程的重要建筑材料，为人类文明作出了伟大的贡献，甚至在目前还被广泛采用。 钢材的大量应用是土木工程的第二次飞跃。 十七世纪70年代开始使用生铁、十九世纪初开始使用熟铁建造桥梁和房屋，这是钢结构出现的前奏。 从十九世纪中叶开始，冶金业冶炼并轧制出抗拉和抗压强度都很高、延性好、质量均匀的建筑钢材，随后又生产出高强度钢丝、钢索 。于是适应发展需要的钢结构得到蓬勃发展。除应用原有的粱、拱结构外，新兴的桁架、框架、网架结构、悬索结构逐渐推广，出现了结构形式百花争艳的局面。 建筑物跨径从砖结构、石结构、木结构的几米、几十米发展到钢结构的百米、几百米，直到现代的千米以上。于是在大江、海峡上架起大桥，在地面上建造起摩天大楼和高耸铁塔，甚至在地面下铺设铁路，创造出前所未有的奇迹。 为适应钢结构工程发展的需要，在牛顿力学的基础上，材料力学、结构力学、工程结构设计理论等就应运而生。施工机械、施工技术和施工组织设计的理论也随之发展，土木工程从经验上升成为科学，在工程实践和基础理论方面都面貌一新，从而促成了土木工程更迅速的发展。 十九世纪20年代，波特兰水泥制成后，混凝土问世了。混凝土骨料可以就地取材，混凝土构件易于成型，但混凝土的抗拉强度很小，用途受到限制。 十九世纪中叶以后，钢铁产量激增，随之出现了钢筋混凝土这种新型的复合建筑材料，其中钢筋承担拉力，混凝土承担压力，发挥了各自的优点。 二十世纪初以来，钢筋混凝土广泛应用于土木工程的各个领域。 从三十年代开始，出现了预应力混凝土。预应力混凝土结构的抗裂性能、刚度和承载能力，大大高于钢筋混凝土结构，因而用途更为广阔。土木工程进入了钢筋混凝土和预应力混凝土占统治地位的历史时期。混凝土的出现给建筑物带来了新的经济、美观的工程结构形式，使土木工程产生了新的施工技术和工程结构设计理论。这是土木工程的又一次飞跃发展。 建造一项工程设施一般要经过勘察、设计和施工三个阶段，需要运用工程地质勘察、水文地质勘察、工程测量、土力学、工程力学、工程设计、建筑材料、建筑设备、工程机械、建筑经济等学科和施工技术、施工组织等领域的知识 ，以及电子计算机和力学测试等技术。因而土木工程是一门范围广阔的综合性学科。随着科学技术的进步和工程实践的发展，土木工程这个学科也已发展成为内涵广泛、门类众多、结构复杂的综合体系。 土木工程是伴随着人类社会的发展而发展起来的。它所建造的工程设施反映出各个历史时期社会经济、文化、科学、技术发展的面貌，因而土木工程也就成为社会历史发展的见证之一。 远古时代，人们就开始修筑简陋的房舍、道路、桥梁和沟澶，以满足简单的生活和生产需要。后来，人们为了适应战争、生产和生活以及宗教传播的需要，兴建了城池、运河、宫殿、寺庙以及其他各种建筑物。 许多著名的工程设施显示出人类在这个历史时期的创造力。例如，中国的长城、都江堰、大运河、赵州桥、应县木塔，埃及的金字塔，希腊的巴台农神庙，罗马的给水工程、科洛西姆圆形竞技场(罗马大斗兽场)，以及其他许多著名的教堂、宫殿等。 产业革命以后，特别是到了20世纪，一方面社会向土木工程提出了新的需求；另一方面，社会各个领域为土木工程的前进创造了良好的条件。因而这个时期的土木工程得到突飞猛进的发展。在世界各地出现了现代化规模宏大的工业厂房、摩天大厦，核电站、高速公路和铁路、大跨桥梁、大直径运输管道长隧道、大运河、大堤坝、大飞机场、大海港以及海洋工程等等。现代土木工程不断地为人类社会创造崭新的物质环境，成为人类社会现代文明的重要组成部分。 土木工程是具有很强的实践性的学科。在早期，土木工程是通过工程实践，总结成功的经验，尤其是吸取失败的教训发展起来的。从17世纪开始，以伽利略和牛顿为先导的近代力学同土木工程实践结合起来，逐渐形成材料力学、结构力学、流体力学、岩体力学，作为土木工程的基础理论的学科。这样土木工程才逐渐从经验发展成为科学。 在土木工程的发展过程中，工程实践经验常先行于理论，工程事故常显示出未能预见的新因素，触发新理论的研究和发展。至今不少工程问题的处理，在很大程度上仍然依靠实践经验。 土木工程技术的发展之所以主要凭借工程实践而不是凭借科学试验和理论研究，有两个原因：一是有些客观情况过于复杂，难以如实地进行室内实验或现场测试和理论分析。例如，地基基础、隧道及地下工程的受力和变形的状态及其随时间的变化，至今还需要参考工程经验进行分析判断。二是只有进行新的工程实践，才能揭示新的问题。例如，建造了高层建筑、高耸塔桅和大跨桥梁等，工程的抗风和抗震问题突出了，才能发展出这方面的新理论和技术。在土木工程的长期实践中，人们不仅对房屋建筑艺术给予很大注意，取得了卓越的成就；而且对其他工程设施，也通过选用不同的建筑材料，例如采用石料、钢材和钢筋混凝土，配合自然环境建造了许多在艺术上十分优美、功能上又十分良好的工程。古代中国的万里长城，现代世界上的许多电视塔和斜张桥，都是这方面的例子。Plays a key role in the development of civil engineering, is the first civil construction materials as the basis for engineering material, followed by the subsequent development of the design theory and construction Whenever there is a fine new building materials, civil engineering will be a leap type People can only rely on the early Earth, wood and other natural materials in the construction activities, and later appeared in brick and tile that artificial materials, so that the first human to break the shackles of natural building Chinese in Eleventh Century BC in the early Western Zhou Dynasty created the The first brick in the fifth Century BC to the third Century BC, the tomb of the Warring States Brick and tile has superior mechanical properties,soil can obtain raw material locally, and easy to Emergence of brick and tile so that people began to widely, a large number of housing construction and urban flood control This civil engineering technology has been rapid Until 18 ~ nineteenth Century, as long as two thousand years, brick and tile has been a major civil engineering construction materials, made a great contribution to the human civilization, and was also widely used in the A large number of applications of steel products is the second leap in civil In seventeenth Century 70 time began using pig iron, the early nineteenth Century began to usewrought iron bridges and the construction of housing, which is a prelude to the emergence of From the beginning of the mid nineteenth Century, the metallurgical industry smelting and rolling out high tensile and compressive strength, good ductility, uniformity of the quality of construction steel, then produce high-strength steel wire, steel And meet the needs for development of steel structure has been In addition to the application of the original beam, arch structure, the new truss, frame, grid structure, and gradually promote the suspension structure,the form of the structure of a hundred flowers contend in beauty From the brick building long-span structure, stone structure, wood structure of a few meters, the development of tens of meters to 100 meters of steel structures, several hundred meters, 1000 meters until So the bridge in the river, channel, since the construction of skyscrapersand high-rise tower on the ground, even in the laying of underground railway, to create ahitherto To meet the development needs of the steel structure engineering, on the basis of Newton's mechanics, material mechanics, structural mechanics, structural engineering design theory would emerge as the times Theoretical design of machinery, construction technology and organization construction also development, civil engineering from the experience of rising to become science, both in engineering practice and theoretical basis for a new, which led tomore rapid development of civil In nineteenth Century 20, Portland cement concrete was Concrete aggregate can obtain raw material locally, easy to concrete structures forming, but the tensile strength of concrete is very small, limited By the middle of the nineteenth Century, the surge in steel production,followed by a composite building material of this new type of reinforced concrete, which bear the tension steel, concrete bear the pressure, to play their respective Since the beginning of twentieth Century, each field of reinforced concrete is widely used in From the beginning of the thirty's, the prestressed The crack resistance, stiffness and bearing capacity of prestressed concrete structure, much higher than the reinforced concrete structure, which uses Civil engineering into the reinforced concrete and prestressed concrete dominant historical Concrete brings the structural form of new economic,aesthetic to the building, civil engineering so that a theory of new construction technology and engineering structure This is a leap in the development of civil A project to build the facilities in general to go through investigation, design and construction in three stages, need to discipline the use of geological prospecting projects, hydro geological survey, engineering survey, soil mechanics, engineering mechanics, engineering design,building materials, construction equipment, engineering machinery, building the economy, and the construction technology, construction and other fields of knowledge, as well as the computer and mechanical testing Civil engineering is therefore a broad range of integrated With the development of science and technology development and engineering practice, the civil engineering disciplines have also been developed into a comprehensivesystem of broad connotation, category numerous, complicated Civil engineering is accompanied by the development of human society and the development It works in the construction of facilities reflect the face of social and economic development,technology, science, culture in every historical period, so the civil engineering has become one of the social and historical development of the In ancient times, people began to build simple houses, roads, bridges and water channel, to meet the simple life and production Later, people in order to adapt to the war, productionand dissemination of religious life and the need to build the city, canals,, palaces, temples and other Many well-known works shown in this historical period of human For example, Chinathe Great Wall, Dujiangyan, the Grande Canale, the Zhaozhou Bridge, the Yingxian Wood Tower, the Pyramid of Egypt, Greece's Parthenon, Rome's water supply project, Kolo Sim Arena(Rome Coliseum), and many other famous churches, After the industrial revolution, especially in twentieth Century, on one hand, the society puts forward new requirements to the civil engineering; on the other hand, each field of the society to create good conditions for the advancement of civil Thus this period of civil engineering has make a spurt of progress of In the rest of the world in the modern large-scale industrial plants, skyscrapers, nuclear power plants, highways and railways, long-span bridge, large diameter pipelines long tunnel, the Grande Canale, big dams, big airport, port and marine engineering Modern civil engineering to create a new physical environment for the human society, has become an important part of modern civilization of human Civil engineering is a very practical In the early days, through the civil engineering practice, summing up successful experience, especially draw lessons from the failure of From the beginning of seventeenth Century, with Galileo and Newton as a combination of pilot with the mechanics of the modern civil engineering practice, gradually formed the mechanical material mechanics, structural mechanics, fluid mechanics, rock mass, as the basis of the theory of civil engineering This experience in civil engineering from the gradually developed into a In the process of the development of civil engineering, engineering practice often first experience in theory, engineering accidents often show a new unforeseen factors, triggering a new theory of research and Yet many engineering problems, still rely on practical experience in the very great
刚好我也在做毕业设计 把我的给你用吧！ Traditional Construction ProceduresAs mentioned before, construction under the traditional construction procedure is performed by While they would like to satisfy the owner and the building designers, contractors have the main objective of making a Hence, their initial task is to prepare a bid price based on an accurate estimate of construction This requires development of a concept for performance of the work and a construction time After a contract has been awarded, contractors must furnish and pay for all materials, equipment, power, labor, and supervision required for The owner compensates the contractors for construction costs and A general contractor assumes overall responsibility for construction of a The contractor engages subcontractors who take responsibility for the work of the various trades required for For example, a plumbing contractor installs the plumbing, an electrical contractor installs the electrical system, and an elevator contractor installs Their contracts are with the general contractor, and they are paid by the general Sometimes, in addition to a general contractor, the owner contracts separately with specialty contractors, such as electrical and mechanical contractors, who perform a substantial amount of the work require for a Such contractors are called prime Their work is scheduled and coordinated by the general contractor, but they are paid directly by the Sometimes also, the owner may use the design-build method and award a contract to an organization for both the design and construction of a Such organizations are called design-build One variation of this type of contract is employed by developers of groups of one-family homes or low-rise apartment The homebuilder designs and constructs the dwellings, but the design is substantially completed before owners purchase the Administration of the construction procedure often is Consequently, some owners seek assistance from an expert, called a professional construction manager, with extensive construction experience, who receives a The construction manager negotiates with general contractors and helps select one to construct the Managers usually also supervise selection of During construction, they help control costs, expedite equipment and material deliveries, and keep the work on In some cases, instead, the owner may prefer o engage a construction program manager, to assist in administrating both design and Construction contractors employ labor that may or may not be Unionized craftspeople are members of unions that are organized by construction trades, such as carpenter, plumber, and electrician unions, Union members will perform only the work assigned to their During construction, all work should be For this purpose, the owner, often through the architect and consultants, engages The field inspectors may be placed under the control of an owner’s representative, who may be titled clerk of the works, architect’s superintendent, engineer’s superintendent, or resident The inspectors have the responsibility of ensuring that construction meets the requirements of the contract documents and is performed under safe Such inspections may be made at frequent In addition, inspections also are made by representatives of one or more governmental They have the responsibility of ensuring that construction meets legal requirements and have little or no concern with detailed conformance with the contract Such legal inspections are made periodically or at the end of certain stages of One agency that will make frequent inspections is the local or state building department, whichever has The purpose of these inspections is to ensure conformance with the local or state building Following is a description of the basic traditional construction procedure for a multistory After the award of a construction contract to a general contractor, the owner may ask the contractor to start a portion of the work before signing of the contract by giving the contractor a letter of intent or after signing of the contract by issuing a written notice to The contractor then obtains construction permits, as required, form governmental agencies, such as the local building, water, sewer, and highway The general contractor plans and schedules construction operations in detail and mobilizes equipment and personnel for the Subcontractors are notified of the contract award and issued letters of intent or awarded subcontracts, then are given, at appropriate times, notices to Before construction starts, the general contractor orders a survey to be made of adjacent structures and terrain, both for the record and to become knowledgeable of local A survey is then made to lay out Field offices for the contractor are erected on or near the If desirable for safety reasons to protect passersby, the required to be removed from the site are demolished and the debris is carted Next, the site is prepared to receive the This work may involve grading the top surface to bring it to the proper elevations, excavating to required depths for basement and foundations, and shifting of utility For deep excavations, earth sides are braced and the bottom is Major construction starts with the placement of foundations, on which the building This is followed by the erection of load-bearing walls and structural Depending on the height of the building, ladders, stairs, or elevators may be installed to enable construction personnel to travel from floor to floor eventually to the Also, hoists may be installed to lift materials to upper If needed, temporary flooring may be placed for use of As the building rises, pipes, ducts, and electric conduit and wiring are Then, permanent floors, exterior walls, and windows are At the appropriate time, permanent elevators are If required, fireproofing is placed for steel Next, fixed partitions are built and the roof and its covering are put is place,Finishing operations There include installation of the following: ceilings; tile; wallboard; wall paneling; plumbing fixtures; heating furnaces; air-conditioning equipment; heating and cooling devices for rooms; escalators; floor coverings; window glass; movable partitions; doors; finishing hardware; electrical equipment and apparatus, including lighting fixtures, switches, transformers, and controls; and other items called for in the drawings and Field offices, fences, bridges, and other temporary construction must be removed from the Utilities, such as gas, electricity, and water, are hooked up to the The sit is landscaped and Finally, the building interior is painted and The owner’s representatives then give the building a final If they find that the structure conforms with the contract documents, the owner accepts the project and gives the general contractor final payment on issuance by the building department of a certificate of occupancy, which indicates that the completed building meets building-code 传统的施工程序众所周知，在传统的施工程序中进行施工的承包商。尽管他们想满足业主和建筑设计师的要求，但是最终还是以赚取利润为主要目标的。因此，他们最初的任务是对编写投标价格的建筑成本进行准确的估计。这就需要进行前期调查的工作并且做出施工时间表。等合约批出后，施工方必须提供所有材料并支付其费用，设备，电力，劳动力。业主此时需要进行必要的监督。一个总承包商承担一个建筑整体的责任。从事分包的承建商则需承担建造工程所需的各个工作。例如，管道承包商安装水管，电业承办商安装电气系统，电梯则由电梯承包商安装。他们与总承包商签订合同，费用由总承包商支付。有时候，除了一个总承包商，还有各种专业承包商，如电气和机械承包商，执行工作时需要与业主签订合同。这种承包商被称为间接承包商。他们的工作，由总承包商协调，但它们都是由业主直接联系。还有些时候，业主可以使用设计建造方法同时兼有设计和建筑施工单位的职能。这些单位被称为设计建造承包商。这方面的一个类型的合同聘用的变化是由一户住宅或低层住宅建筑群的开发。在房屋建筑设计和建造的住房，但设计之前需要由购买房屋的业主完成。施工过程管理往往是困难的。因此，一些业主会去寻求专家的协助，这些专家被称为专业施工经理，他们具有丰富的施工经验。施工经理与总承包商进行谈判，并选择其中一个项目。施工经理通常还监督分包商。在施工期间，它们有助于控制成本，加快运送设备和材料，并保持工作的进度。在依法行政，协助设计和建设的情况下，业主可以选择从事建筑项目经理。建筑承包商雇用的劳动力，一般有大工和小工。大工再建筑工程中从事技术活，如木工，管道工，工会成员和电工工会，小工则执行了分配给他们的工作。在施工期间，一切工作都要验收。因此，业主通过建筑师和监理经常进行督查。可能是名为工程员，建筑师或驻地工程师。作为业主的代表实地视察。核查人员必须确保工程符合合同文件的要求，并在安全的条件下进行的责任。这种检查可作出重复。此外，验收还是需要一个或多个政府机构的代表。他们必须确保工程符合法律要求，并负责检查与合同文件是否一致。这种视察一般定期或在某些阶段施工结束以后进行。地方或国家建设部门具有管辖权。这些检查的目的是确保符合当地或国家的建筑规范。以下是传统多层建筑施工的基本程序。建造开始后合同授予开发商，业主可要求开发商开始施工之前签约给或之后签约发出书面通知的同时另一部分工作继续进行。紧接着施工方根据需要获取建筑许可证，例如当地的建设，供水，污水处理，政府机构和公路部门。总承包商的计划和进度详细施工作业以及动员项目设备和人员。分包商得到通知后，做出签订合同的意向或授予分包合同书，然后给出在适当的时候进行通知。在施工前启动，总承包商要进行的一项调查就是邻近结构和地形，这些都要记录在案，并要熟悉当地情况。这项调查结束以后，随即进行布局建设。承建商的现场办事处都建在施工现场或附近。为了安全起见，必须从脚手架上移除的东西，产生的碎片都要运走。下一步，该网架是为建设工程准备的。这项工作为地下室开挖和基础开挖的深度，以及公用事业管道转移找到正确的标高。深挖掘，土方支撑，底部排出。建筑开始于基础上，然后是承重墙和结构框架的施工。梯子，楼梯，或电梯的安装，可让施工人员往返于各个楼层。此外，可安装卷扬机来运送材料。由于建筑高度的上升，管道，电力管道和线路安装以及永久地板，外墙，窗户和构造的影响。在适当的时候，永久的电梯安装。再需要的情况下可以安装防火卷帘。其次，屋顶等地方也需要安装。精加工工序安装有包括以下内容：天花板，瓷砖，墙板，墙壁镶板，水管装置，加热炉，空气调节设备，加热和冷却室装置;自动扶梯;地板，窗户玻璃;活动板，门;电气设备和仪器，包括照明灯具，开关，变压器，控制器，遵照项目的图纸和规格。外地办事处，围栏，桥梁和其他临时建筑，公共设备，如天然气，电力管道，水管，都连接到建筑上。最后，是建筑物内部的打扫和清洗。业主的代表，会给建设工程作最后检查。如果他们满意并认为符合合同文件，那么业主接受该项目，并交给总承包商的一个占用证书，这表明，总承包商已完成建设，建设部门再根据建筑规范的要求发放最后付款。请采纳。
几年级的啊？
土木工程civil engineering 开题报告Thesis proposal 文献综述Review of the literature
building types and designA building is closely bound up with people，for it provides with the necessary space to work and live in As classified by their use ,buildings are mainly of two types :industrial buildings and civil buildings industrial buildings are used by various factories or industrial production while civil buildings are those that are used by people for dwelling ,employment ,education and other social activities Industrial buildings are factory buildings that are available for processing and manufacturing of various kinds ,in such fields as the mining industry ,the metallurgical industry ,machine building ,the chemical industry and the textile industry factory buildings can be classified into two types single-story ones and multi-story ones he construction of industrial buildings is the same as that of civil buildings however ,industrial and civil buildings differ in the materials used and in the way they are used Civil buildings are divided into two broad categories: residential buildings and public buildings sidential buildings should suit family life ach flat should consist of at least three necessary rooms : a living room ,a kitchen and a toilet public buildings can be used in politics ,cultural activities ,administration work and other services ,such as schools, office buildings, parks ,hospitals ,shops ,stations ,theatres ,gymnasiums ,hotels ,exhibition halls ,bath pools ,and so on all of them have different functions ,which in turn require different design types as Housing is the living quarters for human beings he basic function of housing is to provide shelter from the elements ,but people today require much more that of their housing a family moving into a new neighborhood will to know if the available housing meets its standards of safety ,health ,and comfort a family will also ask how near the housing is to grain shops ,food markets ,schools ,stores ,the library ,a movie theater ,and the community center In the mid-1960’s a most important value in housing was sufficient space both inside and out a majority of families preferred single-family homes on about half an acre of land ,which would provide space for spare-time activities in highly industrialized countries ,many families preferred to live as far out as possible from the center of a metropolitan area ,even if the wage earners had to travel some distance to their work quite a large number of families preferred country housing to suburban housing because their chief aim was to get far away from noise ,crowding ,and confusion he accessibility of public transportation had ceased to be a decisive factor in housing because most workers drove their cars to work people we’re chiefly interested in the arrangement and size of rooms and the number of bedrooms Before any of the building can begin ,plans have to be drawn to show what the building will be like ,the exact place in which it is to go and how everything is to be An important point in building design is the layout of rooms ,which should provide the greatest possible convenience in relation to the purposes for which they are intended in a dwelling house ,the layout may be considered under three categories : “day”, “night” ,and “services” attention must be paid to the provision of easy communication between these areas he “day “rooms generally include a dining-room ,sitting-room and kitchen ,but other rooms ,such as a study ,may be added ,and there may be a hall he living-room ,which is generally the largest ,often serves as a dining-room ,too ,or the kitchen may have a dining alcove he “night “rooms consist of the bedrooms he “services “comprise the kitchen ,bathrooms ,larder ,and water-closets he kitchen and larder connect the services with the day rooms It is also essential to consider the question of outlook from the various rooms ,and those most in use should preferably face south as possible it is ,however ,often very difficult to meet the optimum requirements ,both on account of the surroundings and the location of the roads in resolving these complex problems ,it is also necessary to follow the local town-planning regulations which are concerned with public amenities ,density of population ,height of buildings ,proportion of green space to dwellings ,building lines ,the general appearance of new properties in relation to the neighbourhood ,and so on There is little standardization in industrial buildings although such buildings still need to comply with local town-planning regulations he modern trend is towards light ,airy factory buildings ally of reinforced concrete or metal construction ,a factory can be given a “shed ”type ridge roof ,incorporating windows facing north so as to give evenly distributed natural lighting without sun-glare 翻译：建筑类型和设计建筑物与人们有着紧密的联系，他为人们提供必要的空间，用以工作和生活。根据适用类型不同，建筑物可以分为两类：工业建筑和民用建筑。工业建筑包括各个工厂或工业生产所使用建筑，民用建筑是指那些人们用以居住，就业，教育和其他社会活动的建筑场所。工业建筑的厂房可用于采矿业，冶金工业，机械制造，化学工业和纺织工业等各类领域的加工和制造。厂房可分为两种类型：单层的和多层的。工业建筑也属于建筑的一种。但是，工业建筑与民用建筑所用的材料和建筑方式不同。民用建筑按使用可分为两大类：住宅建筑和公共建筑。住宅建筑要适应家庭生活。每个单位应包括至少三个必要客房：起居室，厨房和厕所。公共建筑可在政治，文化活动，管理工作和其他服务，如学校，写字楼，公园，医院，商店，车站，剧院，体育馆，宾馆，展览馆，洗浴池，等等。他们都有着不同的职能，这反过来又需要不同的设计类型。房屋是用以住人的 其基本功能是提供住房的内容，但今天人们需要更多的住房内容。一个家庭在进入一个新的社区后将知道，现有住房不仅要符合其安全，健康和舒适等标准。还要考虑其附近是否有相应的配套设施，如食品市场，学校，商店，图书馆，电影院，以及社区中心等。在60年代中期住房最重要的价值是足够大的空间和方便的出入交通。大多数家庭会首选约半英亩面积土地的家庭住宅，这样将提供足够的空间的用以业余活动。在高度工业化的国家，许多家庭的首选是那种尽可能远离市中心商业圈的住房，即使距离上班地点不得不有一段距离。相当多的家庭首选是郊区的住房，因为他们的主要目的是要远离噪音，拥挤和混乱。拥有方便的公共交通使得距离不再是一个决定性因素，因为大多数人都是开着自己的汽车去上班了。人们现在主要感兴趣的是户型，房间的大小和卧室的数目。在工程项目开始之前，要做好建筑设计和施工流程,让人提前知道该建筑建成后是什么样子以及下一步应该做什么。在建筑设计中要特别重视房间的布局，其目的是提供最大的便利与可能的用途。在一个住宅建筑设计中，布局可考虑以下三个方面： “白天” ， “夜晚”和“服务”。必须注意这些空间区域之间的连通交流。 “白天”房一般包括餐厅，起居室和厨房，但其他房间可能会增加，如书房，并有可能成为一个大厅。起居室通常是最大的，往往是一个餐厅，也或可能有厨房、凹室等。 “夜间”房间包括卧室、客房。“服务”用房间包括厨房，浴室，储藏室 ，和厕所等。厨房和储藏室需设置在一起，以方便其房间功能的使用。此外，还必须考虑各种客房的朝向问题，当然最好尽可能的将那些经常使用的房间朝南设置。然而，在考虑到周围的环境和地点、道路等多方面因素，往往很难达到最佳要求。在解决这些复杂的问题，还必须按照当地城市规划条例所涉及的对公共设施，人口密度，建筑物高度，绿化面积，建筑红线等的要求，还要考虑到有相邻建筑的情况，等等。尽管工业建筑需要符合当地城市规划条例但很少有标准化的工业楼宇。现代厂房建筑的趋势是轻质、通风。一般的钢筋混凝土结构或钢结构的工厂，可以得到一个“跌”型脊屋顶，把窗户开向北以便使分布均匀的自然采光不会直射进来造成刺眼。
1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。 水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。 设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环境条件等最后确定截面。钢筋混凝土通常是现场浇注的合成材料，它与在工厂中制造的标准的钢结构梁、柱等不同，因此对于上面所提到的一系列因素必须予以考虑。 对结构体系的各个部位均需选定试算截面并进行验算，以确定该截面的名义强度是否足以承受所作用的计算荷载。由于经常需要进行多次试算，才能求出所需的 3 截面，因此设计时第一次采用的数值将导致一系列的试算与调整工作。 选择混凝土截面时，采用试算与调整过程可以使复核与设计结合在一起。因此，当试算截面选定后，每次设计都是对截面进行复核。手册、图表和微型计算机以及专用程序的使用，使这种设计方法更为简捷有效，而传统的方法则是把钢筋混凝土的复核与单纯的设计分别进行处理。 2土方工程 由于和土木工程中任何其他工种的施工方法与费用相比较，土方挖运的施工方法与费用的变化都要快得多，因此对于有事业心的人来说，土方工程是一个可以大有作为的领域。在1935年，目前采用的利用轮胎式机械设备进行土方挖运的方法大多数还没有出现。那是大部分土方是采用窄轨铁路运输，在这目前来说是很少采用的。当时主要的开挖方式是使用正铲、反铲、拉铲或抓斗等挖土机，尽管这些机械目前仍然在广泛应用，但是它们只不过是目前所采用的许多方法中的一小部分。因此，一个工程师为了使自己在土方挖运设备方面的知识跟得上时代的发展，他应当花费一些时间去研究现代的机械。一般说来，有关挖土机、装载机和运输机械的唯一可靠而又最新的资料可以从制造厂商处获得。 土方工程或土方挖运工程指的是把地表面过高处的土壤挖去（挖方），并把它倾卸到地表面过低的其他地方（填方）。为了降低土方工程费用，填方量应该等于挖方量，而且挖方地点应该尽可能靠近土方量相等的填方地点，以减少运输量和填方的二次搬运。土方设计这项工作落到了从事道路设计的工程师的身上，因为土方工程的设计比其他任何工作更能决定工程造价是否低廉。根据现有的地图和标高，道路工程师应在设计绘图室中的工作也并不是徒劳的。它将帮助他在最短的时间内获得最好的方案。 费用最低的运土方法是用同一台机械直接挖方取土并且卸土作为填方。这并不是经常可以做到的，但是如果能够做到则是很理想的，因为这样做既快捷又省钱。拉铲挖土机。推土机和正铲挖土机都能做到这点。拉铲挖土机的工作半径最大。推土机所推运的图的数量最多，只是运输距离很短。拉铲挖土机的缺点是只能挖比它本身低的土，不能施加压力挖入压实的土壤内，不能在陡坡上挖土，而且挖。卸都不准确。 正铲挖土机介于推土机和拉铲挖土机的之间，其作用半径大于推土机，但小于拉铲挖土机。正铲挖土机能挖取竖直陡峭的工作面，这种方式对推土机司机来说是危险的，而对拉铲挖土机则是不可能的。每种机械设备应该进行最适合它的性能的作业。正铲挖土机不能挖比其停机平面低很多的土，而深挖坚实的土壤时，反铲挖土机最适用，但其卸料半径比起装有正铲的同一挖土机的卸料半径则要小很多。在比较平坦的场地开挖，如果用拉铲或正铲挖土机运输距离太远时，则装有轮胎式的斗式铲运机就是比不可少的。它能在比较平的地面上挖较深的土（但只能挖机械本身下面的土），需要时可以将土运至几百米远，然后卸土并在卸土的过程中把土大致铲平。在挖掘硬土时，人们发现在开挖场地经常用一辆助推拖拉机（轮式或履带式），对返回挖土的铲运机进行助推这种施工方法是经济的。一旦铲运机装满，助推拖拉机就回到开挖的地点去帮助下一台铲运机。 斗式铲运机通常是功率非常大的机械，许多厂家制造的铲运机铲斗容量为8 m³，满载时可达10 m³。最大的自行式铲运机铲斗容量为19立方米（满载时为25 m³），由430马力的牵引发动机驱动。 翻斗机可能是使用最为普遍的轮胎式运输设备，因为它们还可以被用来送混凝土或者其他建筑材料。翻斗车的车斗位于大橡胶轮胎车轮前轴的上方，尽管铰接式翻斗车的卸料方向有很多种，但大多数车斗是向前翻转的。最小的翻斗车的容量大约为5立方米，而最大的标准型翻斗车的容量大约为5m³。特殊型式的翻斗车包括容量为4 m³的自装式翻斗车，和容量约为5 m³的铰接式翻斗车。必须记住翻斗车与自卸卡车之间的区别。翻斗车车斗向前倾翻而司机坐在后方卸载，因此有时被称为后卸卡车。 3结构的安全度 规范的主要目的是提供一般性的设计原理和计算方法，以便验算结构的安全度。就目前的趋势而言，安全系数与所使用的材料性质及其组织情况无关，通常把它定义为发生破坏的条件与结构可预料的最不利的工作条件之比值。这个比值还与结构的破坏概率（危险率）成反比。 破坏不仅仅指结构的整体破坏，而且还指结构不能正常的使用，或者，用更为确切的话来说，把破坏看成是结构已经达到不能继续承担其设计荷载的“极限状态”。通常有两种类型的极限状态，即： （1）强度极限状态，它相当于结构能够达到的最大承载能力。其例子包括结构的局部屈曲和整体不稳定性；某此界面失效，随后结构转变为机构；疲劳破坏；引起结构几何形状显著变化的弹性变形或塑性变形或徐变；结构对交变荷载、火灾和爆炸的敏感性。 （2）使用极限状态，它对应着结构的使用功能和耐久性。器例子包括结构失稳之前的过大变形和位移；早期开裂或过大的裂缝；较大的振动和腐蚀。 根据不同的安全度条件，可以把结构验算所采用的计算方法分成： （1）确定性的方法，在这种方法中，把主要参数看作非随机参数。 （2）概率方法，在这种方法中，主要参数被认为是随机参数。此外，根据安全系数的不同用途，可以把结构的计算方法分为： （1）容许应力法，在这种方法中，把结构承受最大荷载时计算得到的应力与经过按规定的安全系数进行折减后的材料强度作比较。 （2）极限状态法，在这种方法中，结构的工作状态是以其最大强度为依据来衡量的。由理论分析确定的这一最大强度应不小于结构承受计算荷载所算得的强度（极限状态）。计算荷载等于分别乘以荷载系数的活载与恒载之和。 把对应于不乘以荷载系数的活载和恒载的工作（使用）条件的应力与规定值（使用极限状态）相比较。根据前两种方法和后两种方法的四种可能组合，我们可以得到一些实用的计算方法。通常采用下面两种计算方法： 确定性的方法，这种方法采用容许应力。 概率方法，这种方法采用极限状态。 至少在理论上，概率法的主要优点是可以科学的考虑所有随机安全系数，然后将这些随机安全系数组合成确定的安全系数。概率法取决于： 1 Reinforced Concrete Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete It is this deviation in the composition of a reinforces concrete section from the homogeneity of 答题实属不易，请楼主谅解，求采纳~
刚好我也在做毕业设计 把我的给你用吧！ Traditional Construction ProceduresAs mentioned before, construction under the traditional construction procedure is performed by While they would like to satisfy the owner and the building designers, contractors have the main objective of making a Hence, their initial task is to prepare a bid price based on an accurate estimate of construction This requires development of a concept for performance of the work and a construction time After a contract has been awarded, contractors must furnish and pay for all materials, equipment, power, labor, and supervision required for The owner compensates the contractors for construction costs and A general contractor assumes overall responsibility for construction of a The contractor engages subcontractors who take responsibility for the work of the various trades required for For example, a plumbing contractor installs the plumbing, an electrical contractor installs the electrical system, and an elevator contractor installs Their contracts are with the general contractor, and they are paid by the general Sometimes, in addition to a general contractor, the owner contracts separately with specialty contractors, such as electrical and mechanical contractors, who perform a substantial amount of the work require for a Such contractors are called prime Their work is scheduled and coordinated by the general contractor, but they are paid directly by the Sometimes also, the owner may use the design-build method and award a contract to an organization for both the design and construction of a Such organizations are called design-build One variation of this type of contract is employed by developers of groups of one-family homes or low-rise apartment The homebuilder designs and constructs the dwellings, but the design is substantially completed before owners purchase the Administration of the construction procedure often is Consequently, some owners seek assistance from an expert, called a professional construction manager, with extensive construction experience, who receives a The construction manager negotiates with general contractors and helps select one to construct the Managers usually also supervise selection of During construction, they help control costs, expedite equipment and material deliveries, and keep the work on In some cases, instead, the owner may prefer o engage a construction program manager, to assist in administrating both design and Construction contractors employ labor that may or may not be Unionized craftspeople are members of unions that are organized by construction trades, such as carpenter, plumber, and electrician unions, Union members will perform only the work assigned to their During construction, all work should be For this purpose, the owner, often through the architect and consultants, engages The field inspectors may be placed under the control of an owner’s representative, who may be titled clerk of the works, architect’s superintendent, engineer’s superintendent, or resident The inspectors have the responsibility of ensuring that construction meets the requirements of the contract documents and is performed under safe Such inspections may be made at frequent In addition, inspections also are made by representatives of one or more governmental They have the responsibility of ensuring that construction meets legal requirements and have little or no concern with detailed conformance with the contract Such legal inspections are made periodically or at the end of certain stages of One agency that will make frequent inspections is the local or state building department, whichever has The purpose of these inspections is to ensure conformance with the local or state building Following is a description of the basic traditional construction procedure for a multistory After the award of a construction contract to a general contractor, the owner may ask the contractor to start a portion of the work before signing of the contract by giving the contractor a letter of intent or after signing of the contract by issuing a written notice to The contractor then obtains construction permits, as required, form governmental agencies, such as the local building, water, sewer, and highway The general contractor plans and schedules construction operations in detail and mobilizes equipment and personnel for the Subcontractors are notified of the contract award and issued letters of intent or awarded subcontracts, then are given, at appropriate times, notices to Before construction starts, the general contractor orders a survey to be made of adjacent structures and terrain, both for the record and to become knowledgeable of local A survey is then made to lay out Field offices for the contractor are erected on or near the If desirable for safety reasons to protect passersby, the required to be removed from the site are demolished and the debris is carted Next, the site is prepared to receive the This work may involve grading the top surface to bring it to the proper elevations, excavating to required depths for basement and foundations, and shifting of utility For deep excavations, earth sides are braced and the bottom is Major construction starts with the placement of foundations, on which the building This is followed by the erection of load-bearing walls and structural Depending on the height of the building, ladders, stairs, or elevators may be installed to enable construction personnel to travel from floor to floor eventually to the Also, hoists may be installed to lift materials to upper If needed, temporary flooring may be placed for use of As the building rises, pipes, ducts, and electric conduit and wiring are Then, permanent floors, exterior walls, and windows are At the appropriate time, permanent elevators are If required, fireproofing is placed for steel Next, fixed partitions are built and the roof and its covering are put is place,Finishing operations There include installation of the following: ceilings; tile; wallboard; wall paneling; plumbing fixtures; heating furnaces; air-conditioning equipment; heating and cooling devices for rooms; escalators; floor coverings; window glass; movable partitions; doors; finishing hardware; electrical equipment and apparatus, including lighting fixtures, switches, transformers, and controls; and other items called for in the drawings and Field offices, fences, bridges, and other temporary construction must be removed from the Utilities, such as gas, electricity, and water, are hooked up to the The sit is landscaped and Finally, the building interior is painted and The owner’s representatives then give the building a final If they find that the structure conforms with the contract documents, the owner accepts the project and gives the general contractor final payment on issuance by the building department of a certificate of occupancy, which indicates that the completed building meets building-code 传统的施工程序众所周知，在传统的施工程序中进行施工的承包商。尽管他们想满足业主和建筑设计师的要求，但是最终还是以赚取利润为主要目标的。因此，他们最初的任务是对编写投标价格的建筑成本进行准确的估计。这就需要进行前期调查的工作并且做出施工时间表。等合约批出后，施工方必须提供所有材料并支付其费用，设备，电力，劳动力。业主此时需要进行必要的监督。一个总承包商承担一个建筑整体的责任。从事分包的承建商则需承担建造工程所需的各个工作。例如，管道承包商安装水管，电业承办商安装电气系统，电梯则由电梯承包商安装。他们与总承包商签订合同，费用由总承包商支付。有时候，除了一个总承包商，还有各种专业承包商，如电气和机械承包商，执行工作时需要与业主签订合同。这种承包商被称为间接承包商。他们的工作，由总承包商协调，但它们都是由业主直接联系。还有些时候，业主可以使用设计建造方法同时兼有设计和建筑施工单位的职能。这些单位被称为设计建造承包商。这方面的一个类型的合同聘用的变化是由一户住宅或低层住宅建筑群的开发。在房屋建筑设计和建造的住房，但设计之前需要由购买房屋的业主完成。施工过程管理往往是困难的。因此，一些业主会去寻求专家的协助，这些专家被称为专业施工经理，他们具有丰富的施工经验。施工经理与总承包商进行谈判，并选择其中一个项目。施工经理通常还监督分包商。在施工期间，它们有助于控制成本，加快运送设备和材料，并保持工作的进度。在依法行政，协助设计和建设的情况下，业主可以选择从事建筑项目经理。建筑承包商雇用的劳动力，一般有大工和小工。大工再建筑工程中从事技术活，如木工，管道工，工会成员和电工工会，小工则执行了分配给他们的工作。在施工期间，一切工作都要验收。因此，业主通过建筑师和监理经常进行督查。可能是名为工程员，建筑师或驻地工程师。作为业主的代表实地视察。核查人员必须确保工程符合合同文件的要求，并在安全的条件下进行的责任。这种检查可作出重复。此外，验收还是需要一个或多个政府机构的代表。他们必须确保工程符合法律要求，并负责检查与合同文件是否一致。这种视察一般定期或在某些阶段施工结束以后进行。地方或国家建设部门具有管辖权。这些检查的目的是确保符合当地或国家的建筑规范。以下是传统多层建筑施工的基本程序。建造开始后合同授予开发商，业主可要求开发商开始施工之前签约给或之后签约发出书面通知的同时另一部分工作继续进行。紧接着施工方根据需要获取建筑许可证，例如当地的建设，供水，污水处理，政府机构和公路部门。总承包商的计划和进度详细施工作业以及动员项目设备和人员。分包商得到通知后，做出签订合同的意向或授予分包合同书，然后给出在适当的时候进行通知。在施工前启动，总承包商要进行的一项调查就是邻近结构和地形，这些都要记录在案，并要熟悉当地情况。这项调查结束以后，随即进行布局建设。承建商的现场办事处都建在施工现场或附近。为了安全起见，必须从脚手架上移除的东西，产生的碎片都要运走。下一步，该网架是为建设工程准备的。这项工作为地下室开挖和基础开挖的深度，以及公用事业管道转移找到正确的标高。深挖掘，土方支撑，底部排出。建筑开始于基础上，然后是承重墙和结构框架的施工。梯子，楼梯，或电梯的安装，可让施工人员往返于各个楼层。此外，可安装卷扬机来运送材料。由于建筑高度的上升，管道，电力管道和线路安装以及永久地板，外墙，窗户和构造的影响。在适当的时候，永久的电梯安装。再需要的情况下可以安装防火卷帘。其次，屋顶等地方也需要安装。精加工工序安装有包括以下内容：天花板，瓷砖，墙板，墙壁镶板，水管装置，加热炉，空气调节设备，加热和冷却室装置;自动扶梯;地板，窗户玻璃;活动板，门;电气设备和仪器，包括照明灯具，开关，变压器，控制器，遵照项目的图纸和规格。外地办事处，围栏，桥梁和其他临时建筑，公共设备，如天然气，电力管道，水管，都连接到建筑上。最后，是建筑物内部的打扫和清洗。业主的代表，会给建设工程作最后检查。如果他们满意并认为符合合同文件，那么业主接受该项目，并交给总承包商的一个占用证书，这表明，总承包商已完成建设，建设部门再根据建筑规范的要求发放最后付款。请采纳。
我发到你的邮箱了
Traditional Construction ProceduresAs mentioned before, construction under the traditional construction procedure is performed by While they would like to satisfy the owner and the building designers, contractors have the main objective of making a Hence, their initial task is to prepare a bid price based on an accurate estimate of construction This requires development of a concept for performance of the work and a construction time After a contract has been awarded, contractors must furnish and pay for all materials, equipment, power, labor, and supervision required for The owner compensates the contractors for construction costs and A general contractor assumes overall responsibility for construction of a The contractor engages subcontractors who take responsibility for the work of the various trades required for For example, a plumbing contractor installs the plumbing, an electrical contractor installs the electrical system, and an elevator contractor installs Their contracts are with the general contractor, and they are paid by the general Sometimes, in addition to a general contractor, the owner contracts separately with specialty contractors, such as electrical and mechanical contractors, who perform a substantial amount of the work require for a Such contractors are called prime Their work is scheduled and coordinated by the general contractor, but they are paid directly by the Sometimes also, the owner may use the design-build method and award a contract to an organization for both the design and construction of a Such organizations are called design-build One variation of this type of contract is employed by developers of groups of one-family homes or low-rise apartment The homebuilder designs and constructs the dwellings, but the design is substantially completed before owners purchase the Administration of the construction procedure often is Consequently, some owners seek assistance from an expert, called a professional construction manager, with extensive construction experience, who receives a The construction manager negotiates with general contractors and helps select one to construct the Managers usually also supervise selection of During construction, they help control costs, expedite equipment and material deliveries, and keep the work on In some cases, instead, the owner may prefer o engage a construction program manager, to assist in administrating both design and Construction contractors employ labor that may or may not be Unionized craftspeople are members of unions that are organized by construction trades, such as carpenter, plumber, and electrician unions, Union members will perform only the work assigned to their During construction, all work should be For this purpose, the owner, often through the architect and consultants, engages The field inspectors may be placed under the control of an owner’s representative, who may be titled clerk of the works, architect’s superintendent, engineer’s superintendent, or resident The inspectors have the responsibility of ensuring that construction meets the requirements of the contract documents and is performed under safe Such inspections may be made at frequent In addition, inspections also are made by representatives of one or more governmental They have the responsibility of ensuring that construction meets legal requirements and have little or no concern with detailed conformance with the contract Such legal inspections are made periodically or at the end of certain stages of One agency that will make frequent inspections is the local or state building department, whichever has The purpose of these inspections is to ensure conformance with the local or state building Following is a description of the basic traditional construction procedure for a multistory After the award of a construction contract to a general contractor, the owner may ask the contractor to start a portion of the work before signing of the contract by giving the contractor a letter of intent or after signing of the contract by issuing a written notice to The contractor then obtains construction permits, as required, form governmental agencies, such as the local building, water, sewer, and highway The general contractor plans and schedules construction operations in detail and mobilizes equipment and personnel for the Subcontractors are notified of the contract award and issued letters of intent or awarded subcontracts, then are given, at appropriate times, notices to Before construction starts, the general contractor orders a survey to be made of adjacent structures and terrain, both for the record and to become knowledgeable of local A survey is then made to lay out Field offices for the contractor are erected on or near the If desirable for safety reasons to protect passersby, the required to be removed from the site are demolished and the debris is carted Next, the site is prepared to receive the This work may involve grading the top surface to bring it to the proper elevations, excavating to required depths for basement and foundations, and shifting of utility For deep excavations, earth sides are braced and the bottom is Major construction starts with the placement of foundations, on which the building This is followed by the erection of load-bearing walls and structural Depending on the height of the building, ladders, stairs, or elevators may be installed to enable construction personnel to travel from floor to floor eventually to the Also, hoists may be installed to lift materials to upper If needed, temporary flooring may be placed for use of As the building rises, pipes, ducts, and electric conduit and wiring are Then, permanent floors, exterior walls, and windows are At the appropriate time, permanent elevators are If required, fireproofing is placed for steel Next, fixed partitions are built and the roof and its covering are put is place,Finishing operations There include installation of the following: ceilings; tile; wallboard; wall paneling; plumbing fixtures; heating furnaces; air-conditioning equipment; heating and cooling devices for rooms; escalators; floor coverings; window glass; movable partitions; doors; finishing hardware; electrical equipment and apparatus, including lighting fixtures, switches, transformers, and controls; and other items called for in the drawings and Field offices, fences, bridges, and other temporary construction must be removed from the Utilities, such as gas, electricity, and water, are hooked up to the The sit is landscaped and Finally, the building interior is painted and The owner’s representatives then give the building a final If they find that the structure conforms with the contract documents, the owner accepts the project and gives the general contractor final payment on issuance by the building department of a certificate of occupancy, which indicates that the completed building meets building-code 传统的施工程序众所周知，在传统的施工程序中进行施工的承包商。尽管他们想满足业主和建筑设计师的要求，但是最终还是以赚取利润为主要目标的。因此，他们最初的任务是对编写投标价格的建筑成本进行准确的估计。这就需要进行前期调查的工作并且做出施工时间表。等合约批出后，施工方必须提供所有材料并支付其费用，设备，电力，劳动力。业主此时需要进行必要的监督。一个总承包商承担一个建筑整体的责任。从事分包的承建商则需承担建造工程所需的各个工作。例如，管道承包商安装水管，电业承办商安装电气系统，电梯则由电梯承包商安装。他们与总承包商签订合同，费用由总承包商支付。有时候，除了一个总承包商，还有各种专业承包商，如电气和机械承包商，执行工作时需要与业主签订合同。这种承包商被称为间接承包商。他们的工作，由总承包商协调，但它们都是由业主直接联系。还有些时候，业主可以使用设计建造方法同时兼有设计和建筑施工单位的职能。这些单位被称为设计建造承包商。这方面的一个类型的合同聘用的变化是由一户住宅或低层住宅建筑群的开发。在房屋建筑设计和建造的住房，但设计之前需要由购买房屋的业主完成。施工过程管理往往是困难的。因此，一些业主会去寻求专家的协助，这些专家被称为专业施工经理，他们具有丰富的施工经验。施工经理与总承包商进行谈判，并选择其中一个项目。施工经理通常还监督分包商。在施工期间，它们有助于控制成本，加快运送设备和材料，并保持工作的进度。在依法行政，协助设计和建设的情况下，业主可以选择从事建筑项目经理。建筑承包商雇用的劳动力，一般有大工和小工。大工再建筑工程中从事技术活，如木工，管道工，工会成员和电工工会，小工则执行了分配给他们的工作。在施工期间，一切工作都要验收。因此，业主通过建筑师和监理经常进行督查。可能是名为工程员，建筑师或驻地工程师。作为业主的代表实地视察。核查人员必须确保工程符合合同文件的要求，并在安全的条件下进行的责任。这种检查可作出重复。此外，验收还是需要一个或多个政府机构的代表。他们必须确保工程符合法律要求，并负责检查与合同文件是否一致。这种视察一般定期或在某些阶段施工结束以后进行。地方或国家建设部门具有管辖权。这些检查的目的是确保符合当地或国家的建筑规范。以下是传统多层建筑施工的基本程序。建造开始后合同授予开发商，业主可要求开发商开始施工之前签约给或之后签约发出书面通知的同时另一部分工作继续进行。紧接着施工方根据需要获取建筑许可证，例如当地的建设，供水，污水处理，政府机构和公路部门。总承包商的计划和进度详细施工作业以及动员项目设备和人员。分包商得到通知后，做出签订合同的意向或授予分包合同书，然后给出在适当的时候进行通知。在施工前启动，总承包商要进行的一项调查就是邻近结构和地形，这些都要记录在案，并要熟悉当地情况。这项调查结束以后，随即进行布局建设。承建商的现场办事处都建在施工现场或附近。为了安全起见，必须从脚手架上移除的东西，产生的碎片都要运走。下一步，该网架是为建设工程准备的。这项工作为地下室开挖和基础开挖的深度，以及公用事业管道转移找到正确的标高。深挖掘，土方支撑，底部排出。建筑开始于基础上，然后是承重墙和结构框架的施工。梯子，楼梯，或电梯的安装，可让施工人员往返于各个楼层。此外，可安装卷扬机来运送材料。由于建筑高度的上升，管道，电力管道和线路安装以及永久地板，外墙，窗户和构造的影响。在适当的时候，永久的电梯安装。再需要的情况下可以安装防火卷帘。其次，屋顶等地方也需要安装。精加工工序安装有包括以下内容：天花板，瓷砖，墙板，墙壁镶板，水管装置，加热炉，空气调节设备，加热和冷却室装置;自动扶梯;地板，窗户玻璃;活动板，门;电气设备和仪器，包括照明灯具，开关，变压器，控制器，遵照项目的图纸和规格。外地办事处，围栏，桥梁和其他临时建筑，公共设备，如天然气，电力管道，水管，都连接到建筑上。最后，是建筑物内部的打扫和清洗。业主的代表，会给建设工程作最后检查。如果他们满意并认为符合合同文件，那么业主接受该项目，并交给总承包商的一个占用证书，这表明，总承包商已完成建设，建设部门再根据建筑规范的要求发放最后付款。
1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。 水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。 设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环境条件等最后确定截面。钢筋混凝土通常是现场浇注的合成材料，它与在工厂中制造的标准的钢结构梁、柱等不同，因此对于上面所提到的一系列因素必须予以考虑。 对结构体系的各个部位均需选定试算截面并进行验算，以确定该截面的名义强度是否足以承受所作用的计算荷载。由于经常需要进行多次试算，才能求出所需的 3 截面，因此设计时第一次采用的数值将导致一系列的试算与调整工作。 选择混凝土截面时，采用试算与调整过程可以使复核与设计结合在一起。因此，当试算截面选定后，每次设计都是对截面进行复核。手册、图表和微型计算机以及专用程序的使用，使这种设计方法更为简捷有效，而传统的方法则是把钢筋混凝土的复核与单纯的设计分别进行处理。 2土方工程 由于和土木工程中任何其他工种的施工方法与费用相比较，土方挖运的施工方法与费用的变化都要快得多，因此对于有事业心的人来说，土方工程是一个可以大有作为的领域。在1935年，目前采用的利用轮胎式机械设备进行土方挖运的方法大多数还没有出现。那是大部分土方是采用窄轨铁路运输，在这目前来说是很少采用的。当时主要的开挖方式是使用正铲、反铲、拉铲或抓斗等挖土机，尽管这些机械目前仍然在广泛应用，但是它们只不过是目前所采用的许多方法中的一小部分。因此，一个工程师为了使自己在土方挖运设备方面的知识跟得上时代的发展，他应当花费一些时间去研究现代的机械。一般说来，有关挖土机、装载机和运输机械的唯一可靠而又最新的资料可以从制造厂商处获得。 土方工程或土方挖运工程指的是把地表面过高处的土壤挖去（挖方），并把它倾卸到地表面过低的其他地方（填方）。为了降低土方工程费用，填方量应该等于挖方量，而且挖方地点应该尽可能靠近土方量相等的填方地点，以减少运输量和填方的二次搬运。土方设计这项工作落到了从事道路设计的工程师的身上，因为土方工程的设计比其他任何工作更能决定工程造价是否低廉。根据现有的地图和标高，道路工程师应在设计绘图室中的工作也并不是徒劳的。它将帮助他在最短的时间内获得最好的方案。 费用最低的运土方法是用同一台机械直接挖方取土并且卸土作为填方。这并不是经常可以做到的，但是如果能够做到则是很理想的，因为这样做既快捷又省钱。拉铲挖土机。推土机和正铲挖土机都能做到这点。拉铲挖土机的工作半径最大。推土机所推运的图的数量最多，只是运输距离很短。拉铲挖土机的缺点是只能挖比它本身低的土，不能施加压力挖入压实的土壤内，不能在陡坡上挖土，而且挖。卸都不准确。 正铲挖土机介于推土机和拉铲挖土机的之间，其作用半径大于推土机，但小于拉铲挖土机。正铲挖土机能挖取竖直陡峭的工作面，这种方式对推土机司机来说是危险的，而对拉铲挖土机则是不可能的。每种机械设备应该进行最适合它的性能的作业。正铲挖土机不能挖比其停机平面低很多的土，而深挖坚实的土壤时，反铲挖土机最适用，但其卸料半径比起装有正铲的同一挖土机的卸料半径则要小很多。在比较平坦的场地开挖，如果用拉铲或正铲挖土机运输距离太远时，则装有轮胎式的斗式铲运机就是比不可少的。它能在比较平的地面上挖较深的土（但只能挖机械本身下面的土），需要时可以将土运至几百米远，然后卸土并在卸土的过程中把土大致铲平。在挖掘硬土时，人们发现在开挖场地经常用一辆助推拖拉机（轮式或履带式），对返回挖土的铲运机进行助推这种施工方法是经济的。一旦铲运机装满，助推拖拉机就回到开挖的地点去帮助下一台铲运机。 斗式铲运机通常是功率非常大的机械，许多厂家制造的铲运机铲斗容量为8 m³，满载时可达10 m³。最大的自行式铲运机铲斗容量为19立方米（满载时为25 m³），由430马力的牵引发动机驱动。 翻斗机可能是使用最为普遍的轮胎式运输设备，因为它们还可以被用来送混凝土或者其他建筑材料。翻斗车的车斗位于大橡胶轮胎车轮前轴的上方，尽管铰接式翻斗车的卸料方向有很多种，但大多数车斗是向前翻转的。最小的翻斗车的容量大约为5立方米，而最大的标准型翻斗车的容量大约为5m³。特殊型式的翻斗车包括容量为4 m³的自装式翻斗车，和容量约为5 m³的铰接式翻斗车。必须记住翻斗车与自卸卡车之间的区别。翻斗车车斗向前倾翻而司机坐在后方卸载，因此有时被称为后卸卡车。 3结构的安全度 规范的主要目的是提供一般性的设计原理和计算方法，以便验算结构的安全度。就目前的趋势而言，安全系数与所使用的材料性质及其组织情况无关，通常把它定义为发生破坏的条件与结构可预料的最不利的工作条件之比值。这个比值还与结构的破坏概率（危险率）成反比。 破坏不仅仅指结构的整体破坏，而且还指结构不能正常的使用，或者，用更为确切的话来说，把破坏看成是结构已经达到不能继续承担其设计荷载的“极限状态”。通常有两种类型的极限状态，即： （1）强度极限状态，它相当于结构能够达到的最大承载能力。其例子包括结构的局部屈曲和整体不稳定性；某此界面失效，随后结构转变为机构；疲劳破坏；引起结构几何形状显著变化的弹性变形或塑性变形或徐变；结构对交变荷载、火灾和爆炸的敏感性。 （2）使用极限状态，它对应着结构的使用功能和耐久性。器例子包括结构失稳之前的过大变形和位移；早期开裂或过大的裂缝；较大的振动和腐蚀。 根据不同的安全度条件，可以把结构验算所采用的计算方法分成： （1）确定性的方法，在这种方法中，把主要参数看作非随机参数。 （2）概率方法，在这种方法中，主要参数被认为是随机参数。此外，根据安全系数的不同用途，可以把结构的计算方法分为： （1）容许应力法，在这种方法中，把结构承受最大荷载时计算得到的应力与经过按规定的安全系数进行折减后的材料强度作比较。 （2）极限状态法，在这种方法中，结构的工作状态是以其最大强度为依据来衡量的。由理论分析确定的这一最大强度应不小于结构承受计算荷载所算得的强度（极限状态）。计算荷载等于分别乘以荷载系数的活载与恒载之和。 把对应于不乘以荷载系数的活载和恒载的工作（使用）条件的应力与规定值（使用极限状态）相比较。根据前两种方法和后两种方法的四种可能组合，我们可以得到一些实用的计算方法。通常采用下面两种计算方法： 确定性的方法，这种方法采用容许应力。 概率方法，这种方法采用极限状态。 至少在理论上，概率法的主要优点是可以科学的考虑所有随机安全系数，然后将这些随机安全系数组合成确定的安全系数。概率法取决于： 1 Reinforced Concrete Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete It is this deviation in the composition of a reinforces concrete section from the homogeneity of 答题实属不易，请楼主谅解，求采纳~
土木工程civil engineering 开题报告Thesis proposal 文献综述Review of the literature